Free Outdoor Pools

Replacing your existing yard lights with ones that contains motion sensors will not only enhance security but provide needed illumination automatically when you come home at night. Since this DYI project involves some basic electrical work, it is a good idea to check any bare wires with a voltage tester before handling them. To replace your existing outdoor security light fixture: Start by turning on the existing yard light and making sure it is working. Turn off the circuit breaker to the fixture and check to be sure the light has gone off. Remove the old light fixture and unscrew the wire nuts holding the wires together in a counterclockwise direction. Attach a bracket to the box to accommodate the center mounting point of the new fixture. Pair each wire in the new fixture with the same color wire from the box, and screw on wire nuts in a clockwise direction to hold them in place. Be sure to ground the fixture as well.

BrightNest’s mission is to make homeowners happy.

Show up early and be forewarned: Spuyten Duyvil Metropolitan Ave. The roomy back patio, open until The Levee Berry St. The patio is small-ish, but boasts a handful of picnic tables complemented by vibrant graffiti that makes the high fences pop.

about leisure. Leisure Outdoor Adventures (LOA) is a premier fishing guide service. At LOA, we want to help you make a memory that will last a lifetime!

Hooking up your new heater. Important facts about installing your Lil’house heater. This is my actual heater, not cleaned up! My stove sits on the East side of my house. The Top rectangular duct is the “heat duct’ going in the house with the warm air, and the box on the lower left side is where the blower is that is the return air coming out of the house to be warmed and ran back through the house.

This is a left Handed model. Remember, the heat duct is the duct off the top of the stove, going thru a wall or window, all your heat comes out in one room, via that duct and is moved thru the house with the return air system. The return air should be located as far away from the heat duct as possible to move the heat thru the house.

You cannot hook the heatduct from the Lil’house heater into your heatduct work in your home!

Music for an outdoor wedding

Coming from a family with a long-standing Arizona fishing history, Ben spent his childhood years split between the desert lakes surrounding the Phoenix area and the high country lakes and streams in the White Mountains near Whiteriver. His diverse fishing education would eventually lead to an unbelievably successful fishing career, both as a guide and as a tournament angler. It was while attending Northern Arizona University in Flagstaff, Arizona on a full ride music scholarship that Ben realized that his passion for fishing could not be ignored.

After college Ben set out and quickly rose through the ranks of professional bass fishing. In the tournament off-season, Ben started guiding for existing guide services that needed help throughout the state. Ben quickly became the most sought after bass guide in Arizona.

Shop builder’s best indoor hook-up dryer vent kit in the dryer vent kits section of

This wikiHow teaches you how to select and set up an antenna for your TV. Steps Preparing to Connect 1 Determine your television’s antenna connector type. Virtually every TV has an antenna input on the back or side; this is where you’ll plug in the antenna. There are two main versions of this input: Coaxial RF – Resembles a threaded cylinder with a hole in the middle. This type of connector is the standard for most modern TVs. IEC – Resembles a smooth cylinder with a smaller cylinder inside of it.

Check your TV’s manual or look up its model number online to double-check the antenna type. You can typically do this by typing in your location and “tv broadcast station” into Google. This will give you an idea of the type of antenna that you’ll need; for example, if the closest station is relatively far away, a standard set of “rabbit ears” won’t be ideal.

Mens Outdoor Shoes

Outdoor wiring projects are not difficult for a do-it-yourselfer, but, for safety reasons, outdoor wiring codes must be followed. Outdoor wiring projects fall into two general categories: Functional lighting illuminates high-use areas such as steps, stairs, gates, walkways, and outdoor grills. Decorative lighting adds dimension and mood to exterior space such as highlighting tress and shrubs with light.

Functional lighting can also be decorative. Local Codes First, contact the municipal building inspector to determine the requirements for outdoor wiring, if the home center or building material outlet where you do business doesn’t know.

How to Hook Up on Tinder On this new dating app, everyone’s looking for no-strings sex. But you can still screw things up, unless you follow these 8 tips.

I chose to attach one end to my back door frame and the other end to a tree in the center of the yard. Screw the eye bolt screws in at each end, preferably at 90 degree angles to the eventual cable. Take into account that the cable WILL sag some in the middle. Put one loopy thing through one eye bolt screw and run your steel cable through it.

Use two of the chain rope clips here — one to secure the cable and loopy thing and a second to neatly hold the end of the cable. Consider whether you will need to stop your dog from reaching either end of the cable. I did not need one on the end by the house, but I did place one about 20 feet from the tree at the other end. Slide any necessary clips on the cable now, along with the pulley. Make sure you slide them on in the right order, so the pulley can run the full length of cable between whatever clips are necessary.

Put the second loopy thing through the second eye bolt screw and thread the cable through it. Use two clips to secure the cable just like you did on the other end. This end is harder, because you have to pull the cable as tight as possible before screwing the clips on. If our cable was longer than feet, I think we would have needed a fence puller to get it nice and tight. I used one to stop Zuki from wrapping her tie out cable around the tree at the far end.

How to Hook an iPhone to a Traditional Projector

Read thru the questions it will help. The answers to the questions are on down below the questions on this page! No, you cannot hook it up to your existing ductwork. All the heat has to come thru the heatduct supplied with the furnace. It needs to come thru a wallk or window. The blower is not big enough to “push” the heat thru your ductwork.

Command Outdoor Window Hooks are perfect for hanging wreaths, signs, thermometers, or other seasonal decorations directly to the outside of your window.

Grounded Reason is supported by a small commission for purchases made through some product links on this website. We do not accept compensation from companies attempting to sway my review of products. Take Back Your Television You are here: Rules may differ from state to state, and in other countries. So, always check your local rules and regulations before doing any work on your house.

I am not a professional antenna installer and there are different variables you must account for depending on your situation when it comes to installing an antenna. This article is for informational purposes on how I grounded my antenna, and I recommend using a professional to safely install and ground an antenna. You can locate a local certified professional using Home Advisor , or calling them at Recently I posted a review of the Mohu Sky outdoor antenna.

An astute reader asked me about grounding the antenna in the comments of the review. Now, as I was replacing an existing outdoor antenna, I simply hooked the antenna up to the already grounded coaxial cable coming off the roof. I inspected the wiring of my antenna with the intention of doing a write up on how it was grounded.

Your browser is out of date.

Well folks, today is the day my outdoor-string-globe-light-dreams become a reality — I created some DIY posts for hanging outdoor string lights on my main deck, which rock. What I ended up doing was quite simple and super cheap: But I only got to that point after coming up with a bunch of convoluted pole options hmm, that sounded wrong , and even attempting and failing at one of them again, sounding wrong.

My failure was not so much with the pole itself but with my method of attachment whereby I hung over the rail, split my wood not one not two but three times, and stripped all my screws in the process is it just me, or are these words sounding really awkward?

Edit Article How to Hook up a Dvd Recorder to a Dvd Player to Record. This article explains how to connect a DVD player to a DVD recorder in order to transfer media from one disk to the other without the use of a computer.

If you intend to fix your shade sails to a fascia, the use of a reinforced fascia support is strongly recommended. The fascia support is used to connect the overhangs of rafters or trusses to fascias ledgers giving a stronger connection between the two. Always make sure the fascia have been beefed up on the back side and attached to the rafters within feet either side of the attachment point.

With sails larger than sqft, you should make sure the rafters have been secured with screws, and not just nails to the tops of the walls. Reinforced Facia Boards Shade Sail Post Footers If additional posts are required, we recommend the use of a minimum of 4 inch, schedule 40 steel pipe or a minimum of 6×6 inch wood treated for outdoors. Posts sizes are determinied by the size of the sail or sails attached to it, what sides they are attached and the height they are attached.

Your local timber supplier or pipe fabricatore can assist you in your sizing.

Lowrance® Hook-7 Base Mid/High DownScan Sonar/GPS Combo Combo

Arrange the planters in a rectangle no more than 10′ apart. Sam Henderson Sam Henderson Secure one end of the string lights to one of the cup hooks with the hook attached to the light, or with cable ties or twist ties if no hook exists. Continue stringing the lights, making an outline of the planters. Secure one end of the string lights to one of the cup hooks with the hook attached to the light, or with cable ties or twist ties if no hook exists.

Make sure this fits by entering your model number.; Put the finishing touches on your indoor retreat with our sturdy hanging chair swivel hook. Designed to work with Byer of Maine’s hanging chairs, this hook holds up to lbs.

Thread any hook, jig or fly, and tie any fishing knot in seconds — without your glasses! This thing really works. Thanks for a great invention. Threader is not designed to clean paint from hook eye. For very small fishhooks, try hanging a weight on the hook to make tying easier! Featured in Outdoor News, This new knot tying tool was invented to make tying the Palomar Knot easy. As most anglers know, the Palomar Knot is consistently the strongest knot known to tie terminal tackle. It is regarded by the International Game Fish Association as the strongest knot known to prevent the hook from slipping off when you have that lunker on the line.

Its great virtue is that it can be safely tied at night with a minimum of practice and now is even easier with the EZty tool. When tying the Palomar Knot, you must double the line and put it through the eye of the hook. This is often the hardest part because it can be a bit difficult to see clearly to thread the eye.

Electrical Help : How to Install a Power Receptacle Outside